Silikon / Glasfaser

1 Produkt

Alle löschen
  • Double Layer Silicone Air Ducting Silicone Hose Auto Silicone Hoses 25mm 1 Metre Black

    Double Layer Silicone Air Ducting

    -70°C to +310°C 2 Ply Fiberglass Steel Helix
    Ab £14.59
    Ab £14.59

Silikon / Glasfaser

Unsere Silikon-/Glasfaser-Rohrkollektion bietet überragende Flexibilität, Hitzebeständigkeit und Haltbarkeit und ist damit die ideale Wahl für Hochtemperaturanwendungen. Diese aus einer Kombination aus Silikon und Glasfaser gefertigten Rohre bieten außergewöhnliche Leistung in anspruchsvollen Umgebungen wie z. B. in der industriellen Belüftung, in Abgassystemen und bei Heizungsanwendungen.

Die hochfeste Glasfaserverstärkung verbessert die strukturelle Integrität des Kanals, während die Silikonauskleidung eine ausgezeichnete thermische Stabilität bietet und sicherstellt, dass der Kanal flexibel und widerstandsfähig gegen extreme Temperaturen, Chemikalien und Abrieb bleibt. Dies macht ihn zu einer bewährten Lösung für Anwendungen, die einen zuverlässigen Luftstrom, Isolierung und Widerstandsfähigkeit gegen raue Bedingungen erfordern.

Unsere Kollektion an Silikon-/Glasfaserkanälen eignet sich perfekt für den Einsatz in Branchen wie der Automobil-, Luft- und Raumfahrt- sowie Fertigungsindustrie und gewährleistet dauerhafte Leistung und Sicherheit selbst in den anspruchsvollsten Umgebungen.

What is silicone air ducting used for?
It is a high-temperature flexible duct for moving air where an ordinary hose would fail - hot air feeds and returns, brake and diff cooling ducts, engine bay ventilation, motorsport cockpit cooling, marine engine room ventilation and industrial hot air handling. The two layers of silicone-coated glass fibre with a steel wire helix give it heat resistance far beyond a plastic or rubber duct.

What temperature will it take?
The operating range is -70C to +310C, which is the reason most people choose it over cheaper ducting. That covers hot air off a radiator or intercooler, brake cooling ducts running close to hot discs, and industrial process air. For comparison, PVC ducting tops out around +65C - if your application is anywhere near hot components, this is the material you need.

What sizes and lengths do you supply?
Internal diameters from 25mm up to 200mm, in 1, 2, 3 and 4 metre lengths. Order by internal diameter to match the spigot or duct outlet it will slide over. Because the wall is flexible, the duct will stretch slightly onto a spigot that is a close fit, which makes for a neat joint.

What is the steel helix for?
The wire helix moulded into the wall stops the duct collapsing under suction and stops it crushing flat if something rests against it. That means it works on both the pressure and the suction side of a fan or blower, and it will hold its bore in a tight installation. Without a helix, any flexible duct will pull shut the moment you apply negative pressure.

Is the double layer construction worth it over single ply?
Yes, for anything demanding. The double layer gives more mechanical strength, better insulation of the air inside the duct, and a longer service life under vibration and heat cycling. Single-ply duct is fine for gentle ventilation work; if the duct will be handled, routed tightly, or run continuously at high temperature, the double layer is the better buy.

What colours can I get?
Black, red, blue and grey. Black and grey are the usual choice for industrial and marine installations where the duct should not draw attention; red and blue are popular on motorsport and show builds where the ducting is visible. The colour is cosmetic only - the specification is identical across all four.

  • Questions about Silikon / Glasfaser?

    Ask our team

  • Need something bespoke?

    View our custom hose guide.

Other Collections